Search | Car Forums | Gallery | Articles | Helper | AF 350Z | IgorSushko.com | Corporate |
| Latest | 0 Rplys |
12-08-2002, 12:01 PM | #166 | |
AF Newbie
Join Date: Jul 2002
Posts: 2
Thanks: 0
Thanked 0 Times in 0 Posts
|
96-99 Saturn procedure verified
I just want to verify that the procedure listed at http://www.automotiveforums.com/vbul...599#post351599 works perfectly... I was able to program 3 remotes to my 96 SL2 with no problems using just a test lead from my multimeter and my 10 year old son. You don't have to be right by the connector with the remotes though, anywhere in range (20 feet-ish) works OK, my son was in the passenger seat. Thanks to all and happy programming!
Dave Pyatt Alliance, Ohio |
|
12-27-2002, 03:15 AM | #167 | |
AF Newbie
Join Date: Dec 2002
Posts: 4
Thanks: 0
Thanked 0 Times in 0 Posts
|
My 95 Suburban has a 12 pin diagnostic connector and is labled with alpha rather than numeric characters. I also have multiple wires that are black with a white stripe. Does anyone know the correct procedure for programming the remote keyless entry with this configuration?
Clark |
|
12-29-2002, 12:15 AM | #168 | |
AF Newbie
Join Date: Dec 2002
Posts: 4
Thanks: 0
Thanked 0 Times in 0 Posts
|
I have my own answer. Someone else talked about this configuration for another vehicle, so I tried it on mine and it worked. Here goes:
1. Short pins A and G and wait for the locks to cycle. (Pin A is in the upper right corner of the plug and Pin G is in the lower left corner of the plug.) 2. While grounded, push one of the buttons on the remote until the locks cycle again. 3. Remove jumper short and try the remote. Mine works fine. Clark |
|
12-29-2002, 07:03 AM | #169 | |
AF Newbie
Join Date: Dec 2002
Posts: 1
Thanks: 0
Thanked 0 Times in 0 Posts
|
97 GMC Remote Programming
I just purchased a new keyless entry transmitter for my 1997 GMC Safari (Yes, I want to keep the van. Don't ask me why.) Could someone please post programming instructions?
Thanks! |
|
01-02-2003, 10:03 AM | #170 | ||
Blah blah blah
|
Re: 2001 pontiac grand am keyless entry
Quote:
|
||
01-02-2003, 11:16 AM | #171 | ||
Blah blah blah
|
Quote:
Transmitter Programming Perform this procedure when any of the following conditions exist: The RKE programming connector (BLK/WHT wire) is grounded (CKT 1455). The RCDLR is replaced. A remote keyless entry transmitter is replaced. A second (up to a total of 4) remote keyless entry transmitter is added. Important If the vehicle has more than one keyless entry transmitter, ensure that all of the keyless entry transmitters are programmed during the same programming sequence. Any keyless entry transmitters that are not programmed will not work correctly. Open the rear compartment lid. Pull aside the right side compartment trim in order to gain access. Refer to Compartment Side Trim Replacement - RH Rear in Body Rear End. Use a jumper wire with alligator clips in order to ground the RKE programming connector. The door locks will lock and unlock. This action indicates that the RCDLR has entered the keyless entry transmitter programming mode. While the programming connector is still grounded, program each of the keyless entry transmitters, one at a time. Press and hold the LOCK and UNLOCK buttons simultaneously on the first keyless entry transmitter. Hold the buttons for 10 seconds. The door locks will lock and unlock. This action indicates that the keyless entry transmitter has been programmed. Repeat Step 4 for the remaining keyless entry transmitters. You may program as many as 4 keyless entry transmitters. Remove the jumper wire from the RKE programming connector terminal. Verify that the keyless entry transmitters operate correctly. Install the right side rear compartment trim. Refer to Compartment Side Trim Replacement - RH Rear in Body Rear End. Close the rear compartment lid. © Copyright General Motors Corporation. All Rights Reserved. -------------------------------------------------------------------------------- Document ID # 611704 2001 Chevrolet/Geo Lumina |
||
01-02-2003, 11:45 AM | #172 | ||
Blah blah blah
|
Re: 2001 CAMARO Z28 KEY FOBS
Quote:
Transmitter Programming Important All transmitters which are to be recognized by the body control module (BCM) must be programmed in a single programming sequence. If the system is placed in program mode it will erase all previously programmed transmitters upon the receipt of the programming signal from the first transmitter. Up to 4 transmitters can be programmed. Do not operate or program the transmitters in the vicinity of other vehicles that are in the keyless entry program mode. This prevents the programming of the transmitters to the incorrect vehicle. Turn the ignition switch to the OFF position. Remove the RADIO (#17) fuse. Cycle the ignition switch from the OFF position to the RUN position 3 times within 5 seconds. The BCM will confirm entry into the programming mode by performing the following actions: Locking both of the doors. Unlocking the driver's door. Releasing the rear compartment lid. Press and hold the LOCK button and the UNLOCK button simultaneously on one transmitter for approximately 15 seconds. The BCM will confirm the programming of that transmitter by performing the following actions: Locking both of the doors. Unlocking the driver's door. Releasing the rear compartment lid. Repeat the previous step to program up to 4transmitters. Replace the RADIO (#17) fuse. Operate the transmitter functions in order to verify correct system operation. © Copyright General Motors Corporation. All Rights Reserved. -------------------------------------------------------------------------------- Document ID # 641006 2001 Chevrolet/Geo Camaro |
||
01-07-2003, 08:00 AM | #173 | ||
Blah blah blah
|
Re: 2001 Pontiac Aztec Remotes
Quote:
Transmitter Programming (Manual Method) Important All transmitters which are to be recognized by the remote control door lock receiver (RCDLR) must be programmed in a single programming sequence. If the system is placed in program mode it will erase all previously programmed transmitters upon the receipt of the programming signal from the first transmitter. Up to four transmitters can be programmed. Do not operate or program the transmitters in the vicinity of other vehicles that are in the keyless entry program mode. This prevents the programming of the transmitters to the incorrect vehicle. The order in which the transmitters are programmed is important. The first transmitter programmed will be transmitter #1, and the second transmitter programmed will be transmitter #2. The number on the transmitters are for reference only: #2 can be programmed as #1 or vice versa. Additional unnumbered transmitters are also available. Use care to program the transmitters correctly. Perform the following steps: Close the vehicle doors. Turn OFF the ignition. Remove the ignition key from the ignition lock cylinder. Press and hold the driver side door lock switch to the unlock position. Insert the ignition key into the ignition lock cylinder and remove the key. (Do not turn the ignition key in the lock cylinder.) Insert the ignition key into the ignition lock cylinder and remove the key. (Do not turn the ignition key in the lock cylinder.) Insert the ignition key into the ignition lock cylinder. (Do not turn the ignition key in the lock cylinder.) Leave the ignition key in the ignition lock cylinder. Release the door lock switch. The body control module (BCM) will sound three beeps in order to verify the Program Mode has been activated. Press the lock and unlock buttons on the keyless entry transmitter simultaneously for approximately 5 seconds. The BCM will sound two beeps in order to verify that the transmitter has been successfully programmed. Perform the previous step to program up to four transmitters. Remove the ignition key in order to exit the Program Mode. Verify the proper operation of each transmitter. |
||
01-07-2003, 08:04 AM | #174 | ||
Blah blah blah
|
Re: 2002 Malibu keyless reprograming
Quote:
|
||
02-02-2003, 02:52 PM | #175 | |
AF Newbie
Join Date: Jan 2003
Posts: 2
Thanks: 0
Thanked 0 Times in 0 Posts
|
How Do You Program a 2001 GMC Safari Keyless Remote?
I just bought a keyless remote fob for my 2001 GMC Safari.
The dealer wants to charge me $40 to program it! How do I do this myself? Do I need to buy a $50 'scan tool' to do this (I'm afraid this is so), or is there another way for me to do it? Please help me if you can. Thank you! :flash: |
|
02-03-2003, 10:28 AM | #176 | |
Blah blah blah
|
BIGGAMESAFARI
2001 GMC SAFARI
Transmitter Programming Important All transmitters which are to be recognized by the remote control door lock receiver (RCDLR) must be programmed in a single programming sequence. If the system is placed in program mode it will erase all previously programmed transmitters upon the receipt of the programming signal from the first transmitter. Up to four transmitters can be programmed. Do not operate or program the transmitters in the vicinity of other vehicles that are in the keyless entry program mode. This prevents the programming of the transmitters to the incorrect vehicle. You may program up to 4 transmitters, using either of the two following procedures: Transmitter Programming Procedure (Method 1 - No Tools Required) Close all the vehicle doors. Insert the ignition key into the ignition lock cylinder. Press and hold the door unlock switch. While holding the door lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF. Release the door unlock switch. The doors will lock and unlock to confirm the program mode. Press and hold the LOCK button and the UNLOCK button simultaneously on one transmitter. After a delay of approximately 15 seconds, the doors will lock and unlock to confirm the programming of that transmitter. Repeat the previous step to program up to four transmitters. Turn the ignition switch to the RUN position in order to exit the keyless entry transmitter mode. Operate the transmitter functions in order to verify correct system operation. |
|
02-04-2003, 02:40 PM | #177 | |
AF Newbie
Join Date: Feb 2003
Location: Owensboro, Kentucky
Posts: 85
Thanks: 0
Thanked 0 Times in 0 Posts
|
Alero remotes
I need help in programming a keyless remote for a 99 Olds Alero. Anyone know the procedure?
Thanks, Mike |
|
02-04-2003, 02:43 PM | #178 | ||
Blah blah blah
|
Re: Alero remotes
Quote:
1999 Oldsmobile Alero -------------------------------------------------------------------------------- Transmitter Programming A remote door lock receiver may have up to 4 different transmitters programmed. You may program a transmitter to more than 1 vehicle providing the remote keyless entry systems are similar. When reprogramming 1 transmitter, reprogram any and all other transmitters (maximum of 4 total per receiver) at the same time in order for the other transmitters to work. Important Leave a window down in the vehicle while reprogramming the remote control door lock receiver system. This procedure will avoid an unintentional lock out if the reprogramming is not performed properly. Turn off the ignition. Utilize a Tech 2 to program the remote door lock receiver. Enter diagnostics (F0). Enter body (F1); select the year (X) and body style (N). Select "Remote Function Actuation" (F3). Select "Special Functions" (F2). Select "Program Transmitters" (F0). Select the number of transmitters to program (1-4) Follow the on-screen instructions; press continue, wait for the locks to cycle, hold the lock and unlock buttons simultaneously for 15-30 seconds, the locks will cycle again. Exit the vehicle. Attempt to lock/unlock the doors to verify the programming. Perform the following steps if the above procedure does not program the transmitter. Reconnect the Tech 2. Enter service programming (F1). Press the "REQUEST INFO" key. Select "Reprogram Existing Module" Exit the vehicle and remove the Tech 2. Follow the existing procedure to reflash the body control module. © Copyright General Motors Corporation. All Rights Reserved. -------------------------------------------------------------------------------- Document ID # 338176 1999 Oldsmobile Alero |
||
02-05-2003, 06:43 AM | #179 | |
AF Newbie
Join Date: Feb 2003
Location: Owensboro, Kentucky
Posts: 85
Thanks: 0
Thanked 0 Times in 0 Posts
|
99 Alero Remote
John,
Thanks very much for the fast response. I jumped ahead of myself in asking for the programming procedures. I first need to determine if the car has the keyless entry option. I bought it used and didn't get any remotes, but it has power everything and I'm hoping it has the option. Any help with how to determine this? Thanks Again, Mike |
|
02-07-2003, 10:46 PM | #180 | |
AF Newbie
Join Date: Feb 2003
Posts: 1
Thanks: 0
Thanked 0 Times in 0 Posts
|
keyless remote 2001 olds silhouette
Just picked up the remotes and the dealer wants a fortune to program any help would be appreciated.
|
|
|
POST REPLY TO THIS THREAD |
|
|