throttlebody
chilebean
11-29-2004, 09:06 PM
95 windstar. I have radiator fluid pouring out (yes out) of the throttlebody to the air filter. intake gasket, head gasket or craked head what do you think? I've had this thing for 2 months.
CoachKarl
11-29-2004, 09:54 PM
This car runs? You can drive it? I guess a crack in the intake manifold. Possibly due to the intake plenum being torqued with an impact tool.
chilebean
11-30-2004, 07:18 AM
95 windstar. I have radiator fluid pouring out (yes out) of the throttlebody to the air filter. intake gasket, head gasket or craked head what do you think? I've had this thing for 2 months.
The car did run when it was only slightly losing fluid, but does not since the pouring out incident
The car did run when it was only slightly losing fluid, but does not since the pouring out incident
DRW1000
11-30-2004, 12:18 PM
Hi Chilibean,
I don't think the Windstar has coolant passages in its intake manifold. Although I am not familiar with the 95 I do have on a car that has the EGR connected a plate that mates with the throttle body. This vehicle (5.0L Ford) also has coolant lines running through this plate. Perhaps the 95 has a similar setup and that there is coolant lines near the intake.
Good luck
I don't think the Windstar has coolant passages in its intake manifold. Although I am not familiar with the 95 I do have on a car that has the EGR connected a plate that mates with the throttle body. This vehicle (5.0L Ford) also has coolant lines running through this plate. Perhaps the 95 has a similar setup and that there is coolant lines near the intake.
Good luck
Dngrsone
11-30-2004, 12:33 PM
I agree with Karl, it sounds like your lower intake manifold is cracked. Do not operate the vehicle any more, don't even crank it over. If a significant amount of coolant gets into a cylinder, you can incur serious damage.
If the vehicle was running when the big gush came, did it stop on its own? If so, you may already have a bent rod, blown piston or bent crankshaft.
A fairly quick way to see if there is would be to pull all the spark plugs and manually turn the crankshaft. I used a 1/2 inch drive ratchet with I think a 3/4 or 5/8 socket on an extension. You will have to turn the crankshaft at least two full revolutions to get each piston through the entire 4-stroke cycle. Taking the accessory belt off will make it easier to turn. Lift the vehicle and go through the wheel well.
If you can run the crank through the full cycle without an increase of resistance, then things are looking good. If the amount of resistance changes, then there is a lower-end problem and you'll need to have the engine pulled. If it looks good so far, you'll want to do compression checks on each cylinder and look for discrepancies-- if one or two cylinders show a lower pressure than the rest, or the pressure leaks out, then you have bigger problems.
If everything is going right and you want to replace the intake manifold yourself, there are a few threads in this forum that would be useful to read. You can search using key words (not necessarily all at once) intake manifold head gasket.
If the vehicle was running when the big gush came, did it stop on its own? If so, you may already have a bent rod, blown piston or bent crankshaft.
A fairly quick way to see if there is would be to pull all the spark plugs and manually turn the crankshaft. I used a 1/2 inch drive ratchet with I think a 3/4 or 5/8 socket on an extension. You will have to turn the crankshaft at least two full revolutions to get each piston through the entire 4-stroke cycle. Taking the accessory belt off will make it easier to turn. Lift the vehicle and go through the wheel well.
If you can run the crank through the full cycle without an increase of resistance, then things are looking good. If the amount of resistance changes, then there is a lower-end problem and you'll need to have the engine pulled. If it looks good so far, you'll want to do compression checks on each cylinder and look for discrepancies-- if one or two cylinders show a lower pressure than the rest, or the pressure leaks out, then you have bigger problems.
If everything is going right and you want to replace the intake manifold yourself, there are a few threads in this forum that would be useful to read. You can search using key words (not necessarily all at once) intake manifold head gasket.
Automotive Network, Inc., Copyright ©2025